Hi everyone, guys. Welcome back to mine
laboratory. I’m Riccardo. Today I want to review and unboxing
of this grinder support angular. is inside the package,
that has arrived a little but treated, because he made a long journey from China to us. I already like the weight … it seems robust. But let’s open it and see what it contains, how it behaves and how it seems to us to use it. Very well … open the envelope containing the box.
I cut the ribbon. I chose the blue one because from the
description, color and thickness of the materials (from the photo), it seemed to me
superior to many others. This is the content within the
Pack. This is quite heavy and robust. The noise you hear is because there are parts in movement. It has a thickness of 5 mm. It’s heavy and
already gives me a good impression. I proceed to assembly. Here are the explanations …
there is the design more than anything else in “exploded” of the various pieces. I proceed with general assembly. This is the
part that will hold our flexible and so all we need for the
assembly is within the same package. Once the main part has been fixed,
we can move on to the stirrups lateral, which will then hold, the grinder attached to the main support. They will be unscrewed
and then, they will have to be fixed on this side. From this other part, and there is this shaped shape that must fit with these. So yes they position correctly. From here or here and should be blocked on this side. And at this point we can start giving the temporary form to support. We do not squeeze much because we need to adjust both the distance and
the orientation of the holes, in low to the grinder. These are spacers and
one must be put on upper part and one part
low. They have a part that has the form of a bolt … on this side then the housing. And it fits. At the end, there will go the rubber that will have to support and vibration of the our angle grinder. In both, once
mounted, it will go this way. Insert all The grommets in the various supports … and i
supports, temporarily on the bracket main, let’s insert the
clamp stop. this is the mounted mount. Sllora boys … it must be said that the
instructions, actually I’m in Chinese. It is also necessary to have a good one
intuition for montarl. It is intuitive. Actually it is not very difficult. Anyway … this must be positioned in this way and you have to fit together,
the original holes for the entrance of the handle grip of the grinder, with the holes of the
of the support. This can be done by doing rotate forward and backward
these screws, which are the ones they will tighten the grinder.
This in the lower part and this in the high part. So, once positioned, you will receive orientation by tilting In the correct way. So approximately, I place it in the so that it seems more correct, matching this hole with the grip hole. We see the
threading through, so they are sure in this way, we are practically
almost perfectly oriented. I fix it temporarily. Ok, I repeat this way. Threading, obviously, of the bolt, it is the same as that
there is on the “standard” handle of all the angle grinders. Now we have our angle grinder,
free to move. To prevent this movement, simply adjust these nuts. Thus it hangs. To do this
regulation, at the end of this pin there is the shape to use the
Allen key supplied. This shaped part, with the inclination, will go down. I’ve got it by mistake put it up, so now you’ll invert it.
ok … I inverted the grommets, so to have a good support.
Now I adjust the distance of these supports, that a little while ago I left on purpose
lenses. So I approach them and make sure that tighten the body of the grinder perfectly. I make a quick adjustment. Then everything will be corrected again,
before putting it into operation. Because it goes done a setup in this tool to do it
go well. Then, we can put the handle. The movement that will do once
finished, it will be this. In this case, as you see, go to
slam on the support. The two allen screws placed on the back, and that I have not yet tight, will allow us to do slide the support sideways, to adjust it to fit ours grinder. So, we are sure it will be in the center … now I can tighten. Ok! We fixed it and adjusted it
approximately 90 degrees. Let’s see now to adjust it again. Our car is almost ready for work. This, if desired, could
be moved also this way. Both for the orientation of the
morse and both because lowering it, it should inevitably slam. So, if you want you could put it here. Using this as a sleigh. Almost almost the groom here. The protection must be inserted making it block here. Here’s how it will look, then, once mounted. This is the handle to lower it. And this is a spring, which obviously will bring back the support in its position. For those wishing to use the electric grinder, it could simply put this support
on the back, then lock the cord to prevent it from going
in front of cutting. Now I put it in function and let’s see how it goes. The blade cover is not perfectly straight, so it must be adjusted. Some accommodations must be made … Obviously for our safety. Ok … let’s proceed with the cut of
this rod and let’s see if he can cut it well. He executed the cut perfectly.
Sorry if it’s not very clean. It is to be regulated and there is to do the setup of the cuts at 90 degrees … but it is very simple intervene on the regulation. there
these are the vines we were talking about a while ago. OK, guys … we tried with the angular grinder with battery and
now let’s try with the electric one. Let’s see the difference. Obviously it cuts well with the one with the
battery, which electric current grinder. Obviously, the current one has benefited electric, because it does not go under stress. The cut came perfect. Okay guys … I thank you for seeing this
video to the full, this review of the support for the angle grinder, taken at the Chinese site at www.bangood.com. It costs € 31. it’s an economic product, but it allows you to hurry up because you will make cuts,
simply by pressing. Support is It was easy to assemble and I tried it
both with the current grinder electric and battery operated.
With both it worked well. Has cut our 10 mm rod
without difficulties. Obviously, then it depends also from which instrument used for
make the cuts. Now I leave you the link in
description, and if you want to buy it you know where to buy it. Now I greet you and you
I thank. I remind you to leave a like to this video, if you liked the video and also to subscribe to my channel. Hello again from Riccardo.